Yes, a Sansui G-8000 Bluetooth connection needs no soldering. Best path: a Bluetooth receiver with RCA output into the AUX input (150 mV line level, with DIN at the same figure, per the manual transcription). If AUX is taken, use a Tape loop. Rated 120 W/ch into 8 ohms with a toroidal transformer and four filter caps per channel, the G-8000 opens this archive's Sansui G series at the top of its mid-seventies power band.
Figures on this page were checked September 2026. Every table row carries its source.
The G-8000 on paper
| Item | Value | Notes | Source |
|---|---|---|---|
| Production run | 1979 | List price about $920; "Pure Power DC Stereo Receiver" designation | CR, HE |
| Power output | 120 W/ch @ 8 Ω | For 4-8 ohm speakers; FR 5 Hz-50 kHz; THD 0.03%; damping factor 60 | HE, CR |
| Phono input | 2.5 mV (MM) | Microphone input at 6 mV; S/N 78 dB (MM) and 95 dB (line) | HE |
| Line inputs | AUX · 2 × Tape | AUX/line and DIN both 150 mV; record outputs 150 mV (line) and 43 mV (DIN); Pre Out 1 V | HE |
| Build | Toroidal + 4 caps/ch | Huge toroidal power transformer, four filter caps per channel, per period coverage | CR |
| Weight | 24.6 kg | Simulated walnut grain finish; 104 transistors, 11 FETs and 7 ICs counted | HE |
Source codes: HE HiFi Engine manual transcription (Wayback snapshot) · CR classicreceivers.com. Data as of September 2026.
The G-8000's input map
AUX input
RecommendedAUX/line sits at 150 mV and the DIN connector carries the same figure. A line-level Bluetooth receiver with RCA output is comfortable here, with the level check worth its minute on any 150 mV input.
Tape monitor loops
Good alternativeTape I and II come with a monitor position, and the record outputs split 150 mV on line and 43 mV on DIN. Take a loop by attaching to its play jacks, turning the monitor to that tape position, and returning it to off afterwards.
Phono or microphone input
Not for line-levelThe MM phono stage wants 2.5 mV and the microphone input wants 6 mV. Bluetooth at line level would overload the pair, and the turntables would lose their inputs.
Getting the G-8000 connected
- AUX takes the feed
Recorders have first call on the tape loops; AUX handles Bluetooth.
- Plug and pair
Bluetooth receiver RCA out into AUX, USB power in, one pairing with your phone.
- Ease the volume up
Volume low, AUX selected, then upward. Fixed/line output on the adapter when the choice exists.
G-8000 quirks worth knowing
- The G series opens with heavy metal (verified): a toroidal power transformer and four filter capacitors per channel are the hardware story period coverage leads with, and the 24.6 kg weight plus the 104-transistor parts count from the manual transcription back it up.
- DC "Pure Power" designation (verified): the G-8000's own marketing line, quoted in the spec context, marks the DC amplifier path that distinguishes the G generation from the earlier 9090 and 8080 flagships documented on this site.
- DIN at full line level (verified): at 150 mV, the DIN tape connection carries the same figure as the line input, unlike the 30 mV DIN record sockets on the older Sansuis; a DIN deck integrates without level surprises.
Before you start with the G-8000
- Bluetooth receiver with RCA output; LDAC or aptX HD the preferred codec set
- RCA cable, 0.5–1 m
- USB supply for the receiver
FAQ
Plug a Bluetooth receiver with RCA output into the AUX input and select AUX. If AUX is occupied, use a Tape input through the tape monitor. No internal modification is needed.
Per the manual transcription: AUX/line 150 mV, DIN 150 mV, MM phono 2.5 mV, and a microphone input at 6 mV, with a line signal-to-noise ratio of 95 dB and Pre Out at 1 V. Record outputs run 150 mV on line and 43 mV on DIN.
Rated 120 W per channel into 8 ohms for speakers of 4 to 8 ohms, with a frequency response of 5 Hz to 50 kHz and 0.03% distortion. Period coverage adds the hardware story: a huge toroidal power transformer and four filter caps per channel.
The G series carries the DC "Pure Power" amplifier designation and the symmetrical big-knob styling period coverage describes, alongside the monitoring and dubbing facilities. This archive documents the 9090 and 8080 as the earlier flagships; the G-8000 opens the G-generation shelf.
blafili B3 Bluetooth Music Receiver
RCA + XLR + optical out, LDAC and aptX HD, OLED status display. Matches the G-8000 line-level inputs without adapters.
- Full specifications (120 W/ch into 8 ohms for 4-8 ohm speakers; frequency response 5 Hz-50 kHz; THD 0.03%; damping factor 60; Mic 6 mV, MM 2.5 mV, DIN 150 mV, line 150 mV; S/N 78 dB MM, 95 dB line; output 150 mV line, 43 mV DIN, 1 V Pre out; dimensions 560 × 201 × 475 mm; weight 24.6 kg; simulated walnut grain finish; 104 transistors, 70 diodes, 11 FETs, 7 ICs): HiFi Engine, Sansui G-8000 manual page (hifiengine.com, bot-gated to direct fetches; verified via Wayback snapshot 20250817195203), accessed 2026-09-25
- Manufactured around 1979, list price about $920, huge toroidal power transformer with four filter caps per channel, inputs for Phono I+II, Tape I+II, AUX, Monitor, Mic, G-series symmetrical styling with huge tuning and volume knobs: classicreceivers.com/sansui-g-8000, accessed 2026-09-25